Vans RV Builders List
Vans Parts Vendors
EAA FAA
Sun n Fun FAA Registry
Oshkosh NTSB
Home Empennage kit Wing Kit Fuselage Kit Finish Kit Power Plant Kit Avionics Paint Interior Home
CENTER SECTION MID FUSE LOWER FUSE  SIDE SKINS ROLLOVER TAIL ATTCH  SEATS PEDALS FUEL FWD FUSE  BUILDERS LOG
Page  23.07 Side Skins    
23.01 23.02 23.03 23.04 23.05 23.06 23.07 23.08      
Step 01: Cut apart the F-1086 Vent Bracket into two F-1086A and two F-1086B Vent Brackets as shown in Figure 1. Cut apart the F-1087 Vent Side into two F-10877B Vent Sides as shown in Figure 2.  
Step 02: Cleco the F-1087A Vent Side, F-1087B Vent Side, F-1092 Vent Door Doubler and F-1093 Vent Door together as shown in Figure 3. Final-Drill #40 the holes common between these parts. This creates the Vent Door Subassembly. Repeat this step to create a second vent door assembly.  
Step 03: Machine countersink the holes in the F-1093 Vent doors for flush rivets on the outboard side of the aircraft.  
Step 04: File the edges of the slot smooth in the F-1087A and F-1087B Vent Sides. Check that an AN525-10R7 Screw smoothly slides along the entire length of the slot.

NOTE: A small block of wood is helpful to hold the tabs to the F-1086 and F-1086B Vent Brackets
 
Step 05: Cleco the F-1086A and F-1086B Vent Brackets and the F-1096 Vent Doubler to the left F-1270 Fuselage Side Skin as shown in Figure 4. Final-Drill #30 the holes common between these parts. Repeat this step for the right side of the aircraft.  
Step 06: Disassemble the F-1086A and F-1086B Vent Brackets and F-1096 Vent Doublers from the fuselage side skins. Disassemble the Vent Door Subassemblies. Deburr all parts.  
Step 07: Rivet the F-1096 Vent Doubler, F-1086A and F1086B Vent Brackets to the F-1270 Fuselage Side Skin as shown in Figure 4. Repeat this step for the right side of the aircraft.  
Step 08: Rivet the F-1087A Vent Slide, F-1087B Vent Slide, F1092 Vent Door Doubler and F-1093 Vent Door together as shown in Figure 3. Repeat this step to create a second vent door subassembly.  
Step 09: Insert the Vent Door Subassembly as shown in Figure 5. Install the hardware through the F-1086A and B Vent Brackets and the slot in the vent door subassembly as shown in Figure 5 ( place a 5610-18-31 Nylon Washer on between the F-1086A andF-1086B Vent Brackets ) Repeat this step for the right side of the aircraft.  
Page  23.07 Side Skins 
23.01 23.02 23.03 23.04 23.05 23.06 23.07 23.08      
CENTER SECTION MID FUSE LOWER FUSE  SIDE SKINS ROLLOVER TAIL ATTCH  SEATS PEDALS FUEL FWD FUSE  BUILDERS LOG
Drill Chart Tap Chart Bolt Chart Nut Chart Rivet Chart Washer Chart Rod Ends Vendors Shop Home
 

Disclaimer : Information contained on this Site may be out of date and /or inaccurate - Please Confirm any important data with a reliable source.