Vans RV Builders List
Vans Parts Vendors
EAA FAA
Sun n Fun FAA Registry
Oshkosh NTSB
Home Empennage kit Wing Kit Fuselage Kit Finish Kit Power Plant Kit Avionics Paint Interior Home
VERTICAL STAB RUDDER ANTI-SERVO TAB  STABILATOR TAILCONE EMP ATTACH  EMP FAIRINGS  BUILDERS LOG
Page 10.06 Tailcone
10.01 10.02 10.03 10.04 10.05 10.06 10.07 10.08 10.09 10.10  
Step 01: Place the F1282-L & R Bottom Left and Right Skins on a flat surface.

08/17/10

Builder Note: Perform Step 10-02-01 and 10-02--02 at this time.
Step 02: Trim the called out material from the F-1282-L Bottom Left Skin as shown in Figure 1.


08/17/10
Step 03: Rivet the F-1284-L & R Shear Clips to the F-1283A & B J-Stiffeners using rivets called out in Figure 2.

01/17/11
Step 04: Cleco the F-1283A & B J Stiffeners to the F-1282-L & R Bottom Left and Right Skins

08/17/10
Step 05: Match-Drill #30 the holes in each of the F-1282-L & R  Bottom Left and Right Skins into the F-1283A & B J-Stiffeners called out in Figure 2.

Remove, clear away chips, deburr and re-cleco.

08/17/10
   
Step 06: Rivet the F-1283A & B J-Stiffeners only to the J-stiffeners of the F-1282-L & R Bottom Left and Right Skins using rivets called out in Figure 2.

01/17/11
Step 07: Place the F-1282- L Bottom Left Skin upside down across two Sawhorses that are at least 38" Tall. Locate the forward sawhorse just forward of where the F-1028 Frame will be, and the rear sawhorse just aft of where the F-1210 Frame will be See Figure 3. Builder note:
Step: 10-06-07, 10-06-08, 10-06-09 and 10-07-01 will be accomplished using my work table and bungee cords from the overhead paint rack.

Step: 10-07-02 and 10-07-03 will be accomplished using my assembly area work stands.
Step 08: Hook the J-stiffener of the F-1208, F-1209 and F-1210 Frames onto the J-stiffener of the 1282-L Bottom Left Skin. Cleco each fuse frame to the left bottom skin.

Step 09: Hook the J-stiffener of the F-1282-R Bottom Right Skin into the j-stiffener cutout of the F-1208, F-1209 and F-1210 Frames. If the J-stiffeners interfere with J-stiffeners cutouts in the fuse frames, either the J-stiffeners can be bent or the J-stiffeners cutouts in the frames can be enlarged Slightly until the J-stiffeners clear. Cleco the bottom right skin to the F-1282-L Bottom Left Skin and frames.

01/17/11
Page 10.06 Tailcone
10.01 10.02 10.03 10.04 10.05 10.06 10.07 10.08 10.09 10.10  
VERTICAL STAB RUDDER ANTI-SERVO TAB  STABILATOR TAILCONE EMP ATTACH  EMP FAIRINGS  BUILDERS LOG
Drill Chart Tap Chart Bolt Chart Nut Chart Rivet Chart Washer Chart Rod Ends Vendors Shop Home
 

Disclaimer : Information contained on this Site may be out of date and /or inaccurate - Please Confirm any important data with a reliable source.